176 lines
7.2 KiB
C++
176 lines
7.2 KiB
C++
// Sample RFM69 sender/node sketch for mailbox motion sensor
|
|
// http://www.lowpowerlab.com/mailbox
|
|
// PIR motion sensor connected to D3 (INT1)
|
|
// When RISE happens on D3, the sketch transmits a "MOTION" msg to receiver Moteino and goes back to sleep
|
|
// It then wakes up every 32 seconds and sends a message indicating when the last
|
|
// motion event happened (days, hours, minutes, seconds ago) and the battery level
|
|
// In sleep mode, Moteino + PIR motion sensor use about ~78uA
|
|
// Make sure you adjust the settings in the configuration section below !!!
|
|
|
|
// **********************************************************************************
|
|
// Copyright Felix Rusu, LowPowerLab.com
|
|
// Library and code by Felix Rusu - felix@lowpowerlab.com
|
|
// Get the RFM69 and SPIFlash library at: https://github.com/LowPowerLab/
|
|
// **********************************************************************************
|
|
// License
|
|
// **********************************************************************************
|
|
// This program is free software; you can redistribute it
|
|
// and/or modify it under the terms of the GNU General
|
|
// Public License as published by the Free Software
|
|
// Foundation; either version 3 of the License, or
|
|
// (at your option) any later version.
|
|
//
|
|
// This program is distributed in the hope that it will
|
|
// be useful, but WITHOUT ANY WARRANTY; without even the
|
|
// implied warranty of MERCHANTABILITY or FITNESS FOR A
|
|
// PARTICULAR PURPOSE. See the GNU General Public
|
|
// License for more details.
|
|
//
|
|
// You should have received a copy of the GNU General
|
|
// Public License along with this program.
|
|
// If not, see <http://www.gnu.org/licenses/>.
|
|
//
|
|
// Licence can be viewed at
|
|
// http://www.gnu.org/licenses/gpl-3.0.txt
|
|
//
|
|
// Please maintain this license information along with authorship
|
|
// and copyright notices in any redistribution of this code
|
|
// **********************************************************************************
|
|
|
|
#include <RFM69.h> //get it here: https://github.com/LowPowerLab/RFM69
|
|
#include <SPI.h> //get it here: https://github.com/LowPowerLab/SPIFlash
|
|
#include <LowPower.h> //get library from: https://github.com/LowPowerLab/LowPower
|
|
//writeup here: http://www.rocketscream.com/blog/2011/07/04/lightweight-low-power-arduino-library/
|
|
|
|
//*********************************************************************************************
|
|
// *********** IMPORTANT SETTINGS - YOU MUST CHANGE/ONFIGURE TO FIT YOUR HARDWARE *************
|
|
//*********************************************************************************************
|
|
#define NODEID 55 //unique for each node on same network
|
|
#define NETWORKID 250 //the same on all nodes that talk to each other
|
|
#define GATEWAYID 1
|
|
//Match frequency to the hardware version of the radio on your Moteino (uncomment one):
|
|
//#define FREQUENCY RF69_433MHZ
|
|
//#define FREQUENCY RF69_868MHZ
|
|
#define FREQUENCY RF69_915MHZ
|
|
#define IS_RFM69HW //uncomment only for RFM69HW! Leave out if you have RFM69W!
|
|
#define ENCRYPTKEY "sampleEncryptKey" //exactly the same 16 characters/bytes on all nodes!
|
|
#define SENDEVERYXLOOPS 4 //each loop sleeps 8 seconds, so send status message every this many loops (default "4" = 32 seconds)
|
|
//*********************************************************************************************
|
|
|
|
#define MOTIONPIN 1 //hardware interrupt 1 (D3)
|
|
#define BATTERYSENSE A7 //through 1Meg+470Kohm and 0.1uF cap from battery VCC - this ratio divides the voltage to bring it below 3.3V where it is scaled to a readable range
|
|
#define LED 9 // Moteinos have LEDs on D9
|
|
//#define BLINK_EN //uncomment to make LED flash when messages are sent, leave out if you want low power
|
|
|
|
#define SERIAL_BAUD 115200
|
|
//#define SERIAL_EN //uncomment this line to enable serial IO debug messages, leave out if you want low power
|
|
#ifdef SERIAL_EN
|
|
#define DEBUG(input) {Serial.print(input); delay(1);}
|
|
#define DEBUGln(input) {Serial.println(input); delay(1);}
|
|
#else
|
|
#define DEBUG(input);
|
|
#define DEBUGln(input);
|
|
#endif
|
|
|
|
RFM69 radio;
|
|
volatile boolean motionDetected=false;
|
|
|
|
void setup() {
|
|
#ifdef SERIAL_EN
|
|
Serial.begin(SERIAL_BAUD);
|
|
#endif
|
|
radio.initialize(FREQUENCY,NODEID,NETWORKID);
|
|
#ifdef IS_RFM69HW
|
|
radio.setHighPower(); //uncomment only for RFM69HW!
|
|
#endif
|
|
radio.encrypt(ENCRYPTKEY);
|
|
pinMode(MOTIONPIN, INPUT);
|
|
attachInterrupt(MOTIONPIN, motionIRQ, RISING);
|
|
char buff[50];
|
|
sprintf(buff, "\nTransmitting at %d Mhz...", FREQUENCY==RF69_433MHZ ? 433 : FREQUENCY==RF69_868MHZ ? 868 : 915);
|
|
DEBUGln(buff);
|
|
}
|
|
|
|
void motionIRQ()
|
|
{
|
|
motionDetected=true;
|
|
//DEBUGln("I");
|
|
}
|
|
|
|
char sendBuf[32];
|
|
byte sendLen;
|
|
byte sendLoops=0;
|
|
unsigned long MLO=0; //MailLastOpen (ago, in ms)
|
|
unsigned long now = 0, time=0, lastSend = 0, temp = 0;
|
|
|
|
void loop() {
|
|
now = millis();
|
|
int batteryReading = analogRead(BATTERYSENSE);
|
|
if (motionDetected && time-MLO > 20000) //avoid duplicates in 20second intervals
|
|
{
|
|
MLO = time; //save timestamp of event
|
|
sprintf(sendBuf, "MOTION BAT:%i", batteryReading);
|
|
sendLen = strlen(sendBuf);
|
|
if (radio.sendWithRetry(GATEWAYID, sendBuf, sendLen))
|
|
{
|
|
DEBUGln(" ok!");
|
|
#ifdef BLINK_EN
|
|
Blink(LED,3);
|
|
#endif
|
|
}
|
|
else DEBUGln(" nothing...");
|
|
radio.sleep();
|
|
motionDetected=false;
|
|
}
|
|
else sendLoops++;
|
|
|
|
//send readings every SENDEVERYXLOOPS
|
|
if (sendLoops>=SENDEVERYXLOOPS)
|
|
{
|
|
sendLoops=0;
|
|
|
|
char periodO='X', periodC='X';
|
|
unsigned long lastOpened = (time - MLO) / 1000; //get seconds
|
|
unsigned long LO = lastOpened;
|
|
char* MLOstr="LO:99d23h59m";
|
|
char* BATstr="BAT:1024";
|
|
char* BATactual="BATA:5.00v";
|
|
|
|
if (lastOpened <= 59) periodO = 's'; //1-59 seconds
|
|
else if (lastOpened <= 3599) { periodO = 'm'; lastOpened/=60; } //1-59 minutes
|
|
else if (lastOpened <= 259199) { periodO = 'h'; lastOpened/=3600; } // 1-71 hours
|
|
else if (lastOpened >= 259200) { periodO = 'd'; lastOpened/=86400; } // >=3 days
|
|
|
|
if (periodO == 'd')
|
|
sprintf(MLOstr, "LO:%ldd%ldh", lastOpened, (LO%86400)/3600);
|
|
else if (periodO == 'h')
|
|
sprintf(MLOstr, "LO:%ldh%ldm", lastOpened, (LO%3600)/60);
|
|
else sprintf(MLOstr, "LO:%ld%c", lastOpened, periodO);
|
|
|
|
//sprintf(BATstr, "BAT:%i", batteryReading);
|
|
float battV = ((float)batteryReading * 3.3 * 9)/(1023*2.976);
|
|
dtostrf(battV, 3,2, BATactual);
|
|
sprintf(sendBuf, "%s BAT:%sv", MLOstr, BATactual);
|
|
sendLen = strlen(sendBuf);
|
|
radio.send(GATEWAYID, sendBuf, sendLen);
|
|
radio.sleep();
|
|
DEBUG(sendBuf); DEBUG(" ("); DEBUG(sendLen); DEBUGln(")");
|
|
lastSend = time;
|
|
#ifdef BLINK_EN
|
|
Blink(LED, 5);
|
|
#endif
|
|
delay(10); motionDetected=false; //fix PIR false positive glitch
|
|
}
|
|
|
|
DEBUGln("LOOP");
|
|
time = time + 8000 + millis()-now + 480; //correct millis() resonator drift, may need to be tweaked to be accurate
|
|
LowPower.powerDown(SLEEP_8S, ADC_OFF, BOD_OFF);
|
|
}
|
|
|
|
void Blink(byte PIN, int DELAY_MS)
|
|
{
|
|
pinMode(PIN, OUTPUT);
|
|
digitalWrite(PIN,HIGH);
|
|
delay(DELAY_MS);
|
|
digitalWrite(PIN,LOW);
|
|
} |